rebbarb/exi_bba/exi_capture.py

"""ExiCapture — EXI byte-capture front-end, clocked by the GC's EXI clock.

Creates the pin-driven clock domains (so the byte FIFOs can name them), wraps
the SPIMode3Slave bit engine, and bridges it to the 24 MHz `sync` domain
through two AsyncFIFOs:

    EXI clock pin (~27 MHz)                  sync (24 MHz, HFOSC)
    ┌─────────────────────┐   rx_fifo  ───►  received bytes (header + data)
    │  SPIMode3Slave      │   (8-bit, exififo_w→sync)
    │  (bit engine)       │   tx_fifo  ◄───  response bytes to drive on MISO
    └─────────────────────┘   (8-bit, sync→exififo_r)

Domains created here
--------------------
    exiclk     EXI clock pin, posedge, async-reset by CS  -- samples MOSI
               and launches MISO one bit early
    exififo_w  EXI clock pin, posedge, RESET-LESS         -- rx FIFO write side
    exififo_r  EXI clock pin, posedge, RESET-LESS         -- tx FIFO read side

The FIFO domains must NOT see CS: resetting one side of an AsyncFIFO
desynchronises its gray pointers against the other side.  They are also both
posedge, because AsyncFIFO instantiates a posedge-only reset CDC internally and
cannot host a negedge side.

Why pin-clocked: oversampling the EXI clock from a faster domain put BIT-level
timing across a CDC boundary (~55 ns of synchroniser latency against a 37 ns
bit), so MISO came out ~2 bits late and the GC read 0x17 as 05 C0.  Clocking
from the pin makes MISO clock-to-Q and leaves these byte FIFOs as the only
crossing, each with a full byte-time (~296 ns) of slack.

TX response timing
------------------
The engine pops tx_fifo once per byte boundary, unconditionally -- there is no
header counter and no slot threshold.  The byte popped at the end of byte N is
presented during byte N+1, so pops during the header drain whatever the
previous transaction left in the FIFO (this replaces the old CS-fall flush),
and the response the register file pushes during the protocol's turnaround
byte lands in data slot 0.

⚠️ Command space has only ONE drain slot (2-byte header), so a command-space
responder must push exactly its bytes and stop -- see the DEVID note in
bba_register_file.py.
"""

from amaranth import *
from amaranth.lib.cdc import FFSynchronizer
from amaranth.lib.fifo import AsyncFIFO

from exi_bba.spi_mode3_slave import SPIMode3Slave

__all__ = ["ExiCapture"]


class ExiCapture(Elaboratable):
    """EXI front-end: SPI bit engine (capture domain) + byte FIFOs to core.

    Physical SPI pins (capture domain)
    ----------------------------------
    spi_clk / spi_mosi / spi_cs_n : raw async inputs from the GC
    spi_miso                       : output to the GC

    Core-facing RX byte stream (core domain, FWFT read side of rx_fifo)
    ------------------------------------------------------------------
    rx_data : current received byte
    rx_rdy  : a received byte is available
    rx_en   : pop (assert for one core cycle to consume rx_data)

    Core-facing TX byte stream (core domain, write side of tx_fifo)
    --------------------------------------------------------------
    tx_data : response byte to enqueue
    tx_en   : write strobe
    tx_rdy  : tx_fifo has room
    """

    def __init__(self, rx_depth=4, tx_depth=2, phase_meter=False):
        self._rx_depth = rx_depth
        self._tx_depth = tx_depth
        self._phase_meter = phase_meter   # diagnostic, see SPIMode3Slave

        # Physical SPI (capture domain, wired to pins by BBATop)
        self.spi_clk  = Signal(init=1)
        self.spi_mosi = Signal()
        self.spi_cs_n = Signal(init=1)
        self.spi_miso = Signal()
        self.miso_next = Signal(init=1)   # for an SB_IO output register

        # Core-facing RX read side
        self.rx_data = Signal(8)
        self.rx_rdy  = Signal()
        self.rx_en   = Signal()

        # Core-facing TX write side
        self.tx_data = Signal(8)
        self.tx_en   = Signal()
        self.tx_rdy  = Signal()

        # Core-facing: high (exi domain) while a transaction is in progress.
        # The register file uses it to stream variable-length (DMA) reads until
        # CS deasserts.
        self.cs_active = Signal()

    def elaborate(self, platform):
        m = Module()

        # ── Clock domains driven by the EXI clock pin ─────────────────────
        # The bit engine is clocked by EXI CLK itself (pin 44 = die (6,0) =
        # global buffer net 6 on the 5k-sg48, so it can drive a real clock
        # network).  Two edges are needed: Mode 3 samples MOSI on the RISING
        # edge and MISO must change on the FALLING edge, between the master's
        # sampling points.
        #
        # Each edge gets TWO domains with the same clock:
        #   *_rst  async-reset by CS -- the bit/byte counters, which must
        #          restart at every transaction
        #   (plain) no reset -- the byte FIFOs.  Resetting only ONE side of an
        #          AsyncFIFO desynchronises its gray pointers and corrupts it,
        #          so the FIFOs must NOT see CS.
        m.domains.exiclk     = cd_p  = ClockDomain(async_reset=True)
        m.domains.exififo_w  = cd_fw = ClockDomain(reset_less=True)
        # NOTE: both FIFO domains are POSEDGE.  AsyncFIFO instantiates a
        # posedge-only reset CDC internally, so a negedge domain cannot host a
        # FIFO side.  The engine pops in `exififo_r` (posedge) and hands the
        # byte to its negedge output stage through a register.
        m.domains.exififo_r  = cd_fr = ClockDomain(reset_less=True)
        m.d.comb += [
            cd_p .clk.eq(self.spi_clk), cd_p .rst.eq(self.spi_cs_n),
            cd_fw.clk.eq(self.spi_clk),
            cd_fr.clk.eq(self.spi_clk),
        ]

        spi = SPIMode3Slave(phase_meter=self._phase_meter)
        m.submodules.spi = spi

        # RX bytes cross exiclk -> sync; TX bytes cross sync -> exififo_r.
        # These are the ONLY crossings left, and each has a whole byte-time
        # (~296 ns at 27 MHz) of slack -- unlike the old design, where
        # bit-level MISO timing crossed a domain with a 37 ns budget.
        rx_fifo = AsyncFIFO(width=8, depth=self._rx_depth,
                            w_domain="exififo_w", r_domain="sync")
        tx_fifo = AsyncFIFO(width=8, depth=self._tx_depth,
                            w_domain="sync", r_domain="exififo_r")
        m.submodules.rx_fifo = rx_fifo
        m.submodules.tx_fifo = tx_fifo

        # ── Physical pins ↔ bit engine ───────────────────────────────────
        m.d.comb += [
            spi.spi_clk .eq(self.spi_clk),
            spi.spi_mosi.eq(self.spi_mosi),
            spi.spi_cs_n.eq(self.spi_cs_n),
            self.spi_miso.eq(spi.spi_miso),
            self.miso_next.eq(spi.miso_next),
        ]

        # ── RX: every received byte → rx_fifo ────────────────────────────
        m.d.comb += [
            rx_fifo.w_data.eq(spi.rx_byte),
            rx_fifo.w_en  .eq(spi.rx_valid),
            self.rx_data  .eq(rx_fifo.r_data),
            self.rx_rdy   .eq(rx_fifo.r_rdy),
            rx_fifo.r_en  .eq(self.rx_en),
        ]

        # ── TX: core pushes responses; the engine pops one per byte-time ──
        # Pops are UNCONDITIONAL (one per byte boundary).  Header pops drain
        # whatever the previous transaction left behind, so no CS-fall flush
        # or slot-threshold logic is needed here any more.
        m.d.comb += [
            tx_fifo.w_data.eq(self.tx_data),
            tx_fifo.w_en  .eq(self.tx_en),
            self.tx_rdy   .eq(tx_fifo.w_rdy),
            spi.tx_byte   .eq(tx_fifo.r_data),
            tx_fifo.r_en  .eq(spi.tx_load),
        ]

        # ── Transaction framing, in the slow domain ──────────────────────
        # CS is slow relative to `exi`, so a plain synchroniser is correct and
        # there is no longer any reason to detect it in a fast domain.
        cs_n_s = Signal(init=1)
        m.submodules.cs_sync = FFSynchronizer(self.spi_cs_n, cs_n_s,
                                              o_domain="sync", init=1)
        cs_n_prev = Signal(init=1)
        m.d.sync += cs_n_prev.eq(cs_n_s)
        m.d.comb += self.cs_active.eq(~cs_n_s)

        return m


# ── Testbench ─────────────────────────────────────────────────────────────

if __name__ == "__main__":
    import sys
    from amaranth.sim import Simulator, Period

    dut = ExiCapture()
    errors = []

    # SPI half-period in capture ticks.  At 54 MHz capture / 27 MHz EXI the real
    # ratio is ~2; use 4 here for a clean, well-oversampled functional check.
    HALF = 4

    # No capture domain any more: the bit engine is clocked by the EXI pin,
    # so drive the SPI clock with real delays instead of counting ticks.
    HP = Period(MHz=54)   # ONE capture-equivalent tick; delays are HP * n

    async def spi_byte(ctx, mosi_val):
        """Clock one SPI Mode 3 byte; return the assembled MISO byte."""
        miso = 0
        for bit in range(7, -1, -1):
            ctx.set(dut.spi_mosi, (mosi_val >> bit) & 1)
            ctx.set(dut.spi_clk, 0)
            await ctx.delay(HP * (HALF))
            miso = (miso << 1) | ctx.get(dut.spi_miso)
            ctx.set(dut.spi_clk, 1)
            await ctx.delay(HP * (HALF))
        return miso

    async def core_drain_rx(ctx, into):
        """Pop one byte from the core RX side if available."""
        if ctx.get(dut.rx_rdy):
            into.append(ctx.get(dut.rx_data))
            ctx.set(dut.rx_en, 1)
            await ctx.tick("sync").repeat(1)
            ctx.set(dut.rx_en, 0)
            return True
        return False

    async def push_tx(ctx, b):
        ctx.set(dut.tx_data, b)
        ctx.set(dut.tx_en, 1)
        await ctx.tick("sync").repeat(1)
        ctx.set(dut.tx_en, 0)

    async def do_txn(ctx, hdr, responses, n_data, rx_seen):
        """One EXI transaction, modelling the REAL protocol shape.

        The engine pops tx_fifo at every byte boundary, so a response must be
        in the FIFO before the LAST header byte ends to land in data slot 0.
        That byte is the protocol's turnaround byte (docs/exi_protocol_real.md)
        and is exactly when the register file pushes.  Pushing after the whole
        header -- as this bench used to -- is one slot too late.
        """
        ctx.set(dut.spi_cs_n, 0)
        ctx.set(dut.spi_clk, 1)
        await ctx.delay(HP * (HALF))
        for h in hdr[:-1]:
            await spi_byte(ctx, h)
            await core_drain_rx(ctx, rx_seen)
        for r in responses:                       # pushed during the turnaround
            await push_tx(ctx, r)
        await spi_byte(ctx, hdr[-1])
        await core_drain_rx(ctx, rx_seen)
        miso = [await spi_byte(ctx, 0x00) for _ in range(n_data)]
        ctx.set(dut.spi_cs_n, 1)
        await ctx.delay(HP * (HALF))
        for _ in range(20):                       # drain data-phase dummies
            await core_drain_rx(ctx, rx_seen)
            await ctx.tick("sync").repeat(1)
        return miso

    async def testbench(ctx):
        rx_seen = []
        await ctx.delay(HP * (2))

        # Real register-space header: [0x80, ah, al, 0x00] -- the trailing
        # byte is the turnaround slot.
        HDR = [0x80, 0x00, 0x12, 0x00]

        # ── T1: header + 2 data bytes read back ──────────────────────────
        miso = await do_txn(ctx, HDR, [0xA5, 0x5A], 2, rx_seen)
        print(f"T1 rx={[hex(b) for b in rx_seen[:4]]}  MISO={[f'0x{b:02X}' for b in miso]}")
        if rx_seen[:4] != HDR:
            errors.append(f"T1 header rx wrong: {[hex(b) for b in rx_seen[:4]]}")
        if miso != [0xA5, 0x5A]:
            errors.append(f"T1 MISO wrong: {[hex(b) for b in miso]}")

        # ── T2: over-push must NOT leak into the next transaction ────────
        # Txn A pushes 2 responses but the GC clocks only 1 data byte, leaving
        # a stale byte in tx_fifo.  Txn B must read its OWN responses.  There
        # is no CS-fall flush any more: the engine's pops during the header
        # drain whatever the previous transaction left behind.
        rx_seen.clear()
        await do_txn(ctx, HDR, [0xA5, 0x5A], 1, rx_seen)   # leaves 0x5A
        rx_seen.clear()
        misoB = await do_txn(ctx, HDR, [0x11, 0x22], 2, rx_seen)
        print(f"T2 MISO after over-push: {[f'0x{b:02X}' for b in misoB]}  (want 0x11 0x22)")
        if misoB != [0x11, 0x22]:
            errors.append(f"T2 stale byte leaked: {[hex(b) for b in misoB]}")

    sim = Simulator(dut)
    sim.add_clock(Period(MHz=24), domain="sync")
    sim.add_testbench(testbench)

    with sim.write_vcd("ExiCapture.vcd"):
        sim.run()

    if errors:
        print("\nFAILURES:")
        for e in errors:
            print(" ", e)
        sys.exit(1)
    else:
        print("\nAll tests passed.")