libogc's EXI functions return '1 on success, <=0 on error', but every call
site tested '== 0'. A -1 error return therefore read as success, so a failed
EXI_Lock or EXI_Select would fall through and the subsequent transfer would
produce garbage reported as a misleading test failure rather than an EXI
error. All six call sites now test <= 0.
Also retries EXI_Lock for ~100 ms: it fails outright rather than blocking when
another subsystem holds the channel, and Swiss or a libogc driver may hold it
briefly -- without the retry a transient collision surfaces as a test failure.
Builds clean with devkitPPC 16.1.0 / GCC 16, no warnings: 172 KB .dol.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
gc_bba_test/ builds a .dol that drives the adapter over raw EXI from the
console and reports pass/fail per test on the TV, navigable with the pad.
Uses libogc's EXI API against EXI0:2 (Serial Port 1) rather than its bba
network driver: driving the register file directly gives each check its own
verdict, so a failure points at a specific register instead of at
'networking'. Six suites - identity, registers, reset/control, EXI link
integrity (including an EXI clock-index sweep), ethernet TX/RX, SPRAM/DMA
streaming.
Encodes the hardware lessons from bring-up so the app cannot mislead:
* the device ID is a one-shot cleared by the first NCRA reset, so it is
reported SKIP on a re-run rather than FAIL
* TI means the frame reached the W5100, NOT the wire - the TX test says so
* register reads clock exactly the requested length (over-clocking
desynchronises the next transaction)
* TXDATA is written one byte per transaction (eff_addr auto-increments)
.devcontainer/Dockerfile gains the devkitPro gamecube-dev group. devkitPro
publishes no .deb on GitHub, so this uses their installer script against
apt.devkitpro.org -- which is 403 from inside the running container's egress
but reachable from a host-side docker build. Rebuild the container to get it.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The TPS25961's exposed pad is GND and the datasheet requires it be connected
to the GND plane (Table 5-1; package note 3 adds a mechanical requirement).
REVIEW.md claimed this was honoured because the footprint is the _ThermalVias
variant -- but the variant alone connects nothing. hardware/TPS25961.kicad_sym
defined pins 1-6 only, with no pin for the exposed pad, so KiCad had nothing to
map onto footprint pad 7 and left it netless: an isolated copper island under
the chip with its thermal vias going nowhere.
Adds pin 7 (GND, power_in, hidden, stacked on pin 4) to the symbol library, the
cached symbol in exi.kicad_sch, and the U13 instance.
PCB updated and verified: U13 pad 7 carries GND on all four elements (both SMD
rects and both thermal vias), R48 placed, EFUSE_OVLO routed, R49 gone. DRC
reports 0 violations, 0 unconnected pads and 0 schematic parity issues -- the
0-unconnected result is what confirms pad 7 is tied into the GND network rather
than merely labelled. The 4 DRC errors previously dismissed as zone-fill
phantoms on this pad are gone, though zones were refilled in the same pass so
that is not proof of cause either way.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Devcontainer now grants libusb access to the FT2232H so iceprog (bitstream) and
pyftdi (FT2232H EEPROM) run inside the container:
- devcontainer.json: --privileged + /dev/bus/usb bind mount
- Dockerfile: sudo (NOPASSWD for vscode; USB nodes are root-owned), libusb-1.0-0,
libftdi1-2, pyftdi
Add the flash-re-bba-rb skill documenting the procedure (bitstream via best swept
seed, optional EEPROM string, troubleshooting, guardrails) and
flash_ftdi_eeprom.py (pyftdi, backup-first, dry-run default) + ftdi_eeprom.conf
value spec.
Bring-up on the repaired V1 unit: bitstream flash VERIFY OK (iceprog
build/seed4/top.bin, capture 58.36 MHz). EEPROM product string CANNOT be
programmed on V1 — U7 is a 93LC46B (128 B), too small for the FT2232H, which
needs a 93LC56B (256 B); the 128 B chip mirrors and the config write fails
verify. This overturns the old REVIEW note "93LC46B = correct for FT2232H"
(that only checked ORG, not size). Board still works blank -> ROM defaults;
iceprog + UART unaffected. Documented in REVIEW.md + TODO.md (swap U7->93LC56B
for V2); flash_ftdi_eeprom.py detects the mirroring and refuses the write.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Store datasheets for the parts actually placed in the current design,
grouped under hardware/re-bba-rb/datasheets/ by sheet (fpga, power,
usb, ethernet). Filenames normalised to the part MPN. All tracked
through git-lfs per .gitattributes (*.pdf).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Roflin
Dennis Brentjes