Getting back to Swiss previously meant power-cycling the console. R boots
/boot.dol from the SD card directly.
It reuses netboot_boot_file(), so there is ONE DOL launcher and one set of
safety checks (MEM1 entry point, section overlap against the reserved staging
region, libfat unmounted before the jump) rather than a second copy to keep in
step.
Confirmed rather than one-touch, and main-menu only: R is an easy trigger to
catch by accident, test results are not saved anywhere, and losing a full run
to a stray press is worse than one extra button press. Inside a suite R would
be easy to hit while navigating, so it is ignored there.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The transfer completes on hardware -- 293/293 blocks, 299908 bytes in 15.7 s --
but roughly a third of blocks needed a retry, and the numbers that say WHY are
printed by the GC and then scrolled away when Swiss boots. So the one side
that knows whether an ACK failed to transmit or was lost on the wire could not
be read.
netboot now stops after writing the SD card and waits for a button press, and
the summary carries the counters that separate the cases:
desc@+0=N +1=M bad=N lapped=N txto=N
txto is the discriminator: it counts ACKs where TI never set, meaning the
frame never reached the W5100. High txto alongside the host's retries points
at the TX path; txto near zero points at frames sent but lost.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Transfer now works on hardware -- the block counter climbs -- but slowly, with
some ACKs missing. It is ROUND-TRIP bound, not bandwidth bound: stop-and-wait
means one block per round trip, so three things dominated and all three were
conservative bring-up choices rather than considered ones.
- Block size 256 -> 1024. A 298 KB image is 1166 blocks at 256 but only 292
at 1024. 256 was chosen to stay near the only multi-page frame ever proven
on hardware (a 342-byte DHCP broadcast); large frames are now safe because
RBFI stops a full ring being overwritten and stop-and-wait keeps exactly
one frame in flight, so five pages of a fourteen-page budget is never
contended. --block 256 remains as a fallback.
- Host ACK timeout 0.5 s -> 0.1 s. The round trip is a few milliseconds on
a LAN, so half a second meant every lost ACK cost half a second.
- The GC's TI poll slept 500 us up to 20 times, costing up to 10 ms per ACK
even when the transmit succeeded immediately -- on every block. It now
polls without sleeping; a bba_r8 is itself tens of microseconds, so a bare
loop samples often enough and returns as soon as TI sets.
Absence of TI is explicitly NOT fatal. TI only means TXFrameDrain handed the
frame to the W5100, so the frame may well have gone out; and if it did not,
the host's retransmit covers it. Blocking longer would slow the common case
to protect against the rare one.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The alignment bug is FIXED -- hardware now reports "frame 1 (342 B) etype=0800
at 12: FF FF FF FF FF FF 00 2B", i.e. broadcast dst at 0, host MAC at 6,
ethertype at 12. Perfectly aligned, correctly received, correctly skipped as
not ours.
So 00 00 00 01 was never a dropped write. It is frame data being read as a
descriptor, because the ring HAS NO OVERFLOW PROTECTION: nothing in the
gateware consumes RRP, so RXFrameAssembler keeps writing and laps the reader
(the real BBA has RBFI for exactly this). The poll loop costs ~5 EXI
transactions per frame (~200 us) while a 100 Mbit link delivers a 342-byte
frame every ~30 us, and the ring is 15 pages -- roughly 3 to 11 frames. Under
continuous traffic pages are reused before they are read. That is also why it
"worked once out of three tries": it is a race against the host's background
traffic.
ring_next() now returns -4 when the writer is more than two thirds of the ring
ahead, and the caller resyncs and continues instead of parsing bytes that
belong to a different frame. The timeout reports seen / bad-descriptor /
lapped counts so the three cases stay distinguishable.
Detection is not prevention, so the app and the README both now say to quiet
the link first with gc-testlink.sh, which sets a static address and takes the
interface out of NetworkManager -- stopping the DHCP client whose 342-byte
broadcasts are the main offender.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Without this, a successful transfer of a BROKEN build stranded you: the only
copy of a working test program had already been overwritten, so there was no
way to attempt another transfer without an SD card reader.
Write order is now temp -> verify -> rotate, and the ordering is the point:
- The image goes to "<name>.tmp" and is read back and compared BEFORE
anything existing is touched. If the transfer, the write or the verify
fails, the build you are running is still on the card untouched and you
can simply try again. Previously a failed write left the destination
half-overwritten.
- On success the existing build is rotated to "<name>.prev.dol" and the temp
file takes its place. So if the NEW build turns out to be broken, boot
the previous one from Swiss and transfer again from there. One generation
back is enough never to need a card reader.
The two extensions are chosen deliberately:
- the temp file has NO .dol extension, because Swiss lists .dol files and a
half-written image Swiss offers to boot is exactly what this avoids;
- the backup KEEPS .dol, because booting it from Swiss is the whole point of
keeping it.
remove()/rename() on a file that is not there is ignored -- that is just the
first update on a fresh card. If the final rename somehow fails, the message
names the .prev.dol path rather than leaving the user to guess where their
working build went.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Previous version launched the image it had just received, which is the one
thing that cannot be made safe: a broken build hangs the console and the
checks can only catch a truncated or non-DOL image, never a plausible but
broken one.
The flow is now receive -> write to SD -> boot /boot.dol:
- netboot_sd_write() mounts the card (auto-detecting SD2SP2, then SD Gecko
slot B, then slot A), writes the image to the path the host asked for,
and READS IT BACK AND COMPARES. A half-written .dol that still parses is
exactly the failure this design exists to avoid, and the card is the one
component here with no other integrity check.
- netboot_boot_file() then loads /boot.dol -- a known-good Swiss -- and
launches that instead.
So the only image this ever jumps into is one that was already known good. A
broken test build costs nothing: Swiss comes up and can load anything,
including the previous build. If the SD write or verify fails, nothing is
launched at all and the menu is still there.
The destination path travels in the DONE frame rather than being baked in, so
the host decides where the build lands (send-dol.py --dest, default
/gc_bba_test.dol).
libfat is unmounted before the jump: leaving the card mounted hands the next
image a filesystem libfat still thinks it owns, on an EXI channel it is about
to reinitialise.
Note the SD Gecko in memory-card slot A shares EXI channel 0 with the BBA
(channel 0, device 2). libogc arbitrates, but SD2SP2 is on its own channel
and avoids the question -- hence the detection order.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The launcher committed in b438960 would have hung the console, and reviewing
it against Dennis's suggestion to test with Swiss's boot.dol is what surfaced
it -- Swiss is known-good, so a hang could only have been the launcher, but I
would not have been able to tell that from "the transfer is broken".
Two distinct defects, both from the same oversight -- a DOL's sections load
from 0x80003100 upward, which is exactly where this program is running:
1. The copier was an ordinary C function in .text, so it overwrote its OWN
instructions partway through the copy.
2. The image was staged in a memalign'd buffer, which the destination sections
can overwrite while it is still being read from.
Fixes:
- netboot_stub.S: the copy/zero/cache-flush/jump sequence in position
independent assembly, copied into reserved memory and executed THERE. It
has no globals, no literal pool, no TOC references and no calls, because
any of those would read from the address it was LINKED at rather than the
one it is RUNNING at. It also does the dcbf/icbi pass the C version was
doing through DCFlushRange -- without it the CPU executes stale icache
lines at the entry point.
- netboot_reserve(): carves the top of MEM1 and hands it to
SYS_SetArena1Hi() so neither libogc nor malloc allocates there. Called
FIRST in main(), before the framebuffer.
- netboot_launch(): verifies every text/data section AND bss against the
reserved region and refuses (-3) if any would land on it, instead of
corrupting the staged image or the copier mid-flight. Also hands the new
image a stack inside the reserved tail.
The app now tells you on screen to send Swiss's boot.dol first, and the README
explains why: the launcher and the transfer can each be broken independently
and a hang looks identical, so the first send should be an image whose success
is unmistakable.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Copying to SD and rebooting is now the slowest part of the loop. Z in the
test app pulls a new .dol over the adapter and launches it.
Deliberately NOT built on an IP stack. Frames carry a private ethertype
(0x88B5, IEEE 802 local experimental 1) and a 12-byte header, so there is no
ARP, no IP, no checksums, and no libogc network driver competing with our raw
driver for the EXI channel. It reuses exactly the two paths the suite already
proves on hardware: bba_tx_bytes() for TX and the SPRAM ring at RRP for RX.
A side benefit is that each update is a few hundred round trips through that
path -- a soak test we did not have.
STOP-AND-WAIT is load-bearing, not laziness. The gateware does not consume
RRP, so RXFrameAssembler can overwrite ring pages the GC has not read yet;
there is no overflow protection. One block in flight means the ring never
holds more than one unread frame, so the missing protection cannot bite. Both
the header and the README say not to make this a sliding window without adding
RBFI-style protection first.
Failure behaviour, so a bad update never costs a power cycle:
- 30 s idle with no frames, or 5 s mid-transfer, aborts to the menu rather
than hanging.
- A duplicate block is RE-ACKed rather than ignored, because a duplicate
means our previous ACK was lost and re-ACKing is what lets the host move
on.
- netboot_receive() re-asserts the NCRA SR bit first: an earlier test may
have left receive disabled, and then this would wait forever for frames
the gateware is not storing.
- netboot_launch() refuses an image whose entry point or first text section
is not in MEM1 instead of jumping into a mis-parsed header.
The jump itself is the one unavoidable risk: once sections are copied and
interrupts are off, a bad image hangs the console hard enough to need a power
cycle. The MEM1 check is what stands between a truncated transfer and that.
Host side is scripts/send-dol.py (AF_PACKET, needs sudo). The GC's MAC is
discovered from its first ACK, so neither side needs an address configured.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
libogc's EXI functions return '1 on success, <=0 on error', but every call
site tested '== 0'. A -1 error return therefore read as success, so a failed
EXI_Lock or EXI_Select would fall through and the subsequent transfer would
produce garbage reported as a misleading test failure rather than an EXI
error. All six call sites now test <= 0.
Also retries EXI_Lock for ~100 ms: it fails outright rather than blocking when
another subsystem holds the channel, and Swiss or a libogc driver may hold it
briefly -- without the retry a transient collision surfaces as a test failure.
Builds clean with devkitPPC 16.1.0 / GCC 16, no warnings: 172 KB .dol.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
gc_bba_test/ builds a .dol that drives the adapter over raw EXI from the
console and reports pass/fail per test on the TV, navigable with the pad.
Uses libogc's EXI API against EXI0:2 (Serial Port 1) rather than its bba
network driver: driving the register file directly gives each check its own
verdict, so a failure points at a specific register instead of at
'networking'. Six suites - identity, registers, reset/control, EXI link
integrity (including an EXI clock-index sweep), ethernet TX/RX, SPRAM/DMA
streaming.
Encodes the hardware lessons from bring-up so the app cannot mislead:
* the device ID is a one-shot cleared by the first NCRA reset, so it is
reported SKIP on a re-run rather than FAIL
* TI means the frame reached the W5100, NOT the wire - the TX test says so
* register reads clock exactly the requested length (over-clocking
desynchronises the next transaction)
* TXDATA is written one byte per transaction (eff_addr auto-increments)
.devcontainer/Dockerfile gains the devkitPro gamecube-dev group. devkitPro
publishes no .deb on GitHub, so this uses their installer script against
apt.devkitpro.org -- which is 403 from inside the running container's egress
but reachable from a host-side docker build. Rebuild the container to get it.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Roflin