Previous version launched the image it had just received, which is the one
thing that cannot be made safe: a broken build hangs the console and the
checks can only catch a truncated or non-DOL image, never a plausible but
broken one.
The flow is now receive -> write to SD -> boot /boot.dol:
- netboot_sd_write() mounts the card (auto-detecting SD2SP2, then SD Gecko
slot B, then slot A), writes the image to the path the host asked for,
and READS IT BACK AND COMPARES. A half-written .dol that still parses is
exactly the failure this design exists to avoid, and the card is the one
component here with no other integrity check.
- netboot_boot_file() then loads /boot.dol -- a known-good Swiss -- and
launches that instead.
So the only image this ever jumps into is one that was already known good. A
broken test build costs nothing: Swiss comes up and can load anything,
including the previous build. If the SD write or verify fails, nothing is
launched at all and the menu is still there.
The destination path travels in the DONE frame rather than being baked in, so
the host decides where the build lands (send-dol.py --dest, default
/gc_bba_test.dol).
libfat is unmounted before the jump: leaving the card mounted hands the next
image a filesystem libfat still thinks it owns, on an EXI channel it is about
to reinitialise.
Note the SD Gecko in memory-card slot A shares EXI channel 0 with the BBA
(channel 0, device 2). libogc arbitrates, but SD2SP2 is on its own channel
and avoids the question -- hence the detection order.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Copying to SD and rebooting is now the slowest part of the loop. Z in the
test app pulls a new .dol over the adapter and launches it.
Deliberately NOT built on an IP stack. Frames carry a private ethertype
(0x88B5, IEEE 802 local experimental 1) and a 12-byte header, so there is no
ARP, no IP, no checksums, and no libogc network driver competing with our raw
driver for the EXI channel. It reuses exactly the two paths the suite already
proves on hardware: bba_tx_bytes() for TX and the SPRAM ring at RRP for RX.
A side benefit is that each update is a few hundred round trips through that
path -- a soak test we did not have.
STOP-AND-WAIT is load-bearing, not laziness. The gateware does not consume
RRP, so RXFrameAssembler can overwrite ring pages the GC has not read yet;
there is no overflow protection. One block in flight means the ring never
holds more than one unread frame, so the missing protection cannot bite. Both
the header and the README say not to make this a sliding window without adding
RBFI-style protection first.
Failure behaviour, so a bad update never costs a power cycle:
- 30 s idle with no frames, or 5 s mid-transfer, aborts to the menu rather
than hanging.
- A duplicate block is RE-ACKed rather than ignored, because a duplicate
means our previous ACK was lost and re-ACKing is what lets the host move
on.
- netboot_receive() re-asserts the NCRA SR bit first: an earlier test may
have left receive disabled, and then this would wait forever for frames
the gateware is not storing.
- netboot_launch() refuses an image whose entry point or first text section
is not in MEM1 instead of jumping into a mis-parsed header.
The jump itself is the one unavoidable risk: once sections are copied and
interrupts are off, a bad image hangs the console hard enough to need a power
cycle. The MEM1 check is what stands between a truncated transfer and that.
Host side is scripts/send-dol.py (AF_PACKET, needs sudo). The GC's MAC is
discovered from its first ACK, so neither side needs an address configured.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Roflin