d35688390ec901a5ce9e8c87a78c17ec42a7a722
6 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
 Roflin
|
91c3bf0ece |
Clock the EXI bit engine from the EXI pin: timing closes on all 8 seeds
Replaces the PLL-fed 54 MHz `capture` domain, which oversampled the GC's
27 MHz EXI clock 2x and so put BIT-level timing across a CDC boundary: the
engine's view of the clock lagged the pin by 2 FFSynchronizer stages plus a
register (~55 ns) against a 37 ns bit time, so MISO came out ~2 bits late and
the GC read 0x17 as 05 C0. No amount of oversampling fixes that -- 54 MHz
gives only 2 ticks per bit and the part cannot close the 81 MHz that 3x needs.
The engine is now clocked by the pin itself (pin 44 = global buffer input net
6, no board change), making MISO clock-to-Q. ExiCapture creates four domains:
exiclk (posedge, samples MOSI), exiclk_n (negedge, drives MISO), both
async-reset by CS, plus reset-less exififo_w/exififo_r for the byte FIFO sides
-- reset-less because resetting one side of an AsyncFIFO desynchronises its
gray pointers, and posedge because AsyncFIFO has a posedge-only reset CDC
internally and cannot host a negedge side.
Also removes the SPRAM response FIFO. The DMA read was one byte late because
the round trip did not fit the protocol's turnaround byte; the arbiter already
exposed valid/ready, so the FIFO bought a cycle of latency and nothing else.
The response is handled outside the FSM (the reply lands in RHDR_PAD, not
SPRAM_STREAM) with a one-entry hold for when tx_fifo is momentarily full.
The PLL was left instantiated but unused after the rewrite; removing it frees
the hard macro and pin 35 (which stays unconnected only because the board is
already built that way). This is what lifted the pass rate:
domain target before after
clk (sync) 24 MHz 28.1-30.2 26.4-32.2 8/8
capture_clk 54 MHz 2 of 8 PASS (gone)
EXI pin domain 27 MHz -- 45.6-64.4 8/8
Best seed 3: clk 32.18 MHz, EXI 55.86 MHz. The binding constraint has FLIPPED
-- `clk` (1.10-1.34x) is now tighter than the EXI domain (1.69-2.39x) -- so
synth.py ranks seeds by worst RELATIVE margin, not by the EXI number.
synth.py could not have scored this design at all: it required the vanished
capture_clk, and its regex '(\w+)' cannot match nextpnr's exi_clk_$glb_clk
(no $ in \w). add_clock_constraint was also landing on the wrong net -- under
EXI_J4 the clock is the AND of two pads, not either pad -- so nextpnr silently
fell back to a 12 MHz default and under-optimised the whole EXI domain.
Testbenches:
- spi_mode3_slave had lost its testbench entirely in the rewrite. Restored
with a strict Mode 3 master (changes MOSI on the falling edge, samples MISO
in the clock-low phase) and MUTATION-TESTED: flipping either clock edge in
the RTL makes it fail. Both of those bugs previously reached silicon
against a lax master that parked MOSI well before the edge.
- exi_j4 T2/T3 returned [0,4,2,2]. Real bug: the engine latches the FIFO head
at each byte boundary, so a 2-byte command header leaves only ONE drain
slot. DEVID streamed zeros until CS and left two stale bytes -- one too
many -- so the NEXT enumeration came back a slot late. DEVID now pushes
exactly four bytes and stops. Register-space reads may still over-push:
their 4-byte header gives three drain slots.
- Dead ports removed from SPIMode3Slave (hdr_bytes, frame_start, cs_active,
byte_idx) and the mode2 parameter is gone -- there is one correct edge
convention and it is now enforced by tests.
All 14 module suites pass, plus bba_top at EXI_HALF=1/2/8.
CLAUDE.md: rewrote the clocking, CDC inventory and module tables; marked the
2026-09-30 capture_clk measurements historical; and corrected the line in
"Critical Protocol Notes" that still stated the INVERTED edge convention
("MOSI sampled on falling, MISO driven on rising" is Mode 2) -- the original
implementation followed that doc error.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
|
||
|
Roflin
|
02239466fb |
Merge the exi and sync domains into one
bba_top wired ClockSignal("sync") to ClockSignal("exi"), so the two "domains"
were always the same physical clock net. Everything between them -- six
AsyncFIFOs and three PulseSynchronizers -- was pure latency and logic for a
crossing that did not exist.
* the six AsyncFIFOs become plain SyncFIFOs
* the three PulseSynchronizers become wires
* BBARegisterFile and ExiCapture move from m.d.exi to m.d.sync
* the exi ClockDomain is gone; HFOSC drives sync directly
The SPRAM request write port is also combinational now. A registered w_en
costs a 24 MHz cycle, and the protocol's turnaround byte (~296 ns at 27 MHz)
has no cycles to spare.
Passing: bba_register_file, spram_arbiter, rx_frame_assembler, tx_frame_drain,
w5100_parallel_master, uart_shell, status_panel. bba_top at EXI_HALF=1
(27 MHz, the hardware rate) passes device ID, PAR read/write, NWAYS, RWP and
the 34-byte TX frame.
STILL OPEN: the SPRAM/DMA read is one byte late. Removing the CDC was not
enough -- the remaining round trip is the rx crossing (exiclk->sync, a REAL
CDC, ~125 ns) plus FSM decode plus the spram_req FIFO, arbiter, SPRAM access
and spram_rsp FIFO, which still exceeds the turnaround byte. Next step: now
that it is all one domain, drop the two SPRAM FIFOs entirely and give the
register file a direct request/grant port on the arbiter -- that should take
the round trip to ~2-3 cycles and fit.
exi_capture and exi_j4 testbenches still assert removed behaviour (the CS-fall
flush and the old MISO slot timing) and need rewriting for the clocked engine.
Still WIP -- do not flash.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
|
||
|
Roflin
|
da21a080d9 |
TX passes at 27 MHz; remaining DMA offset traced to needless exi/sync CDC
The TX failure was a TESTBENCH artifact, not a design bug. Between
transactions the bench raised CS for one HP -- 18.5 ns at EXI_HALF=1 -- but
cs_active reaches the exi domain through a 2-stage FFSynchronizer at 24 MHz,
so the register file never saw one transaction end and swallowed the next
one's header as write data. A real host leaves microseconds between
exi_deselect() and the next exi_select(). With a realistic gap the 34-byte TX
frame now matches byte-for-byte at the hardware rate.
At EXI_HALF=1 (27 MHz) bba_top now passes device ID, PAR read/write, NWAYS,
RWP and TX. The one remaining failure is the SPRAM/DMA stream, offset by
exactly one byte.
Root cause of that offset, and it is not architectural: bba_top.py:171 does
m.d.comb += ClockSignal("sync").eq(ClockSignal("exi"))
so exi and sync are LITERALLY THE SAME CLOCK NET. Every AsyncFIFO between
them is pure overhead. The SPRAM round trip pays two needless CDC crossings
(~6 cycles, ~250 ns) on top of the arbiter and SPRAM access, giving ~375 ns
against the ~170 ns the protocol's turnaround byte actually leaves once the rx
crossing is subtracted. Register reads are unaffected because their response
is immediate; only SPRAM is late.
Fix direction: merge the two domains and replace the exi<->sync AsyncFIFOs and
PulseSynchronizers with plain SyncFIFOs/signals. That removes the latency,
drops a lot of logic, and cannot change behaviour because the clocks are
already identical.
Known failing, both testing removed behaviour rather than new bugs:
* exi_capture's own testbench asserts the CS-fall flush and the old MISO
slot timing; the flush no longer exists (header pops drain the FIFO).
* exi_j4's T3 re-enumerate is off by a byte.
Still WIP -- do not flash.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
|
||
|
Roflin
|
a3b3e052bc |
WIP rewrite: clock the EXI bit engine from the EXI clock pin
Replaces 54 MHz oversampling with a slave clocked by EXI CLK itself:
exiclk posedge sample MOSI (Mode 3 samples on edge 2)
exiclk_n negedge drive MISO (must settle between the master's samples)
CS_N async reset for both
EXI CLK (pin 44) is at die (6,0) = global buffer net 6 on the 5k-sg48, so it
can drive a real clock network with no board change.
This removes the capture domain entirely. Bit-level timing no longer
crosses a clock boundary -- MISO is clock-to-Q instead of 3 ticks of a foreign
clock -- and the only crossings left are the byte FIFOs, which have a whole
byte-time (~296 ns) of slack rather than a fraction of a bit.
AsyncFIFO needs a posedge clock for its internal reset CDC, so the FIFO sides
use reset-less POSEDGE domains on the same pin; the engine pops on the posedge
and hands the byte to the negedge output stage through a register. The FIFOs
must not see CS: resetting one side of an AsyncFIFO desynchronises its gray
pointers.
Two bugs found and fixed along the way:
* one pop per byte boundary is all that is needed -- pops during the header
drain whatever the previous transaction left (replacing the CS-fall flush)
and the turnaround-byte push lands in data slot 0. No slot-threshold or
header-length logic at all.
* rx_byte/rx_valid had to become COMBINATIONAL. Registered, they need one
more clock edge, and after a transaction's final bit the clock stops and
CS rises -- so the last byte of every transaction was lost (a 4-byte write
landed as DE AD BE 00, a 34-byte TX as 15 bytes).
At the HARDWARE rate (EXI_HALF=1, 27 MHz) the device ID, NWAYS, PAR
read/write and the W5100->SPRAM RX path now all pass -- none of which has ever
worked at 27 MHz before. Testbenches now drive the SPI clock with real
delays, since there is no capture domain to count ticks against.
STILL BROKEN: the SPRAM/DMA stream is offset by one byte (its round trip
exceeds the single turnaround byte), and TX lands 15 of 34 bytes. Do not
flash this yet.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
|
||
|
Roflin
|
2458884160 |
Rework the EXI decoder to the real GC<->BBA protocol
Replaces the invented 2-byte header (addr split across both bytes, 2-bit
length field) with the protocol libogc and Swiss actually speak:
command (bit7=0, 6-bit reg) [reg, 00, 00, data] one 4-byte transfer
register (bit7=1, 16-bit reg) [0x80|w<<6, ah, al, 00] + data until CS
This was not an optimisation: the old decoder read Swiss's NWAYS read
(80 00 31 00) as 'write 0x31 to NCRA', and bit 0 of 0x31 is RESET, so every
register read would have reset the device.
Changes:
* 16-bit address; no length field -- register reads and writes now stream
until CS, like the SPRAM path already did
* RHDR_LO starts the SPRAM fetch as soon as the address completes, using
the trailing header byte as the prefetch window the protocol provides
* command space serves EXI regs 0x02/0x03 (interrupt mask/status), the only
two Swiss uses
* EXI_GetID gets its own path: it offers just ONE header byte of warning, so
the first ID byte is pushed the instant byte 0 identifies the query
Two timing subtleties, both found by simulation and commented in place:
* MISO is driven LIVE from the tx FIFO head, so a byte pushed while the pad
byte is on the wire appears in the pad slot. A filler byte is parked
there (MISO is don't-care through the header) so the first real response
lands in data slot 0.
* the prefetch must be one-shot; re-firing while waiting for the pad byte
consumed the register stream early and shifted reads by a byte.
All testbenches updated to the real format and passing: bba_register_file
(7), bba_top (8 incl. the full W5100->SPRAM->GC loop and TX), exi_j4,
exi_capture, spi_mode3_slave, tx_frame_drain, spram_arbiter,
rx_frame_assembler, w5100_parallel_master. gc_bba_test rebuilt against the
new protocol.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
|
||
|
Roflin
|
9a7eb54801 |
exi_j4: shared AND-merge helper + enumeration testbench
Factors the EXI_J4 pad merge out of synth.py so the synthesis path and the test exercise the same code. Verifies the device ID (04 02 02 00) enumerates over SP1 with J4 idle, over J4 with SP1 idle, and over SP1 again afterwards, plus a register read via J4 and the full cs_n truth table. Co-Authored-By: Claude Opus 5 <noreply@anthropic.com> |