Hardware with RBFI active: "timeout mid-transfer (5 seen, 18 bad desc, 0
lapped)", plus a frame dump of "1E FF FF FF FF FF FF 00".
Three things that tells us:
- lapped = 0, so the ring is no longer being overwritten. RBFI works and
overflow is eliminated as the cause.
- got > 0 ("mid-transfer"), so some blocks DID arrive and match.
- 0x1E is 286 & 0xFF, the low byte of total_len, followed by the full
six-byte broadcast MAC and then 0x00. The frame body is intact but starts
one byte later than the reader expects.
18 of 23 frames rejected while 5 parsed in the SAME run means the offset
VARIES frame to frame -- a race in the assembler, not a constant. Simulation
does not reproduce it: T2/T5 put the descriptor at +0 and the body at +4 with
the write port both free-running and stalled 1-in-3, and the mutation controls
for both known handshake bugs fail as expected. So the cause is still unknown
and I am not going to guess at it a fifth time.
ring_next() now LOCATES the descriptor instead of assuming +0: it probes
offsets 0 and 1 and takes whichever yields a plausible length (> 4 descriptor
bytes, <= a legal frame), then reads the body and advances RRP from that same
offset. A length is a strong discriminator, so this is a measurement rather
than a guess, and it both lets the transfer proceed and COUNTS the split --
"desc@+0=N +1=M" on success and on timeout. That distribution is the
measurement needed to find the real gateware bug.
Also trimmed the on-screen guidance: the console holds ~25 lines and the
explanatory text was pushing the failure diagnostics off the top, which cost
two blind round trips. Status during a transfer is now one line, and the
menu blurb one line.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Two separate problems, one of which was hiding the other.
1. The diagnostics were unreadable. do_netboot() printed them and returned,
and the caller's draw_main() redrew immediately and wiped the screen -- so
two consecutive failures were reported only as "a short flash" with no
detail, and the error code alone was not enough to act on. nb_pause() now
holds the screen until a button is pressed, on every failure path.
This cost two blind round trips, each of which needs a hand copy of the
.dol to the SD card. Printing a diagnosis and then erasing it is worse
than not printing one.
2. The default block was 1024 bytes, making ~1050-byte frames that span FIVE
of the SPRAM ring's 15 pages. The only multi-page frame ever proven on
this hardware is the 342-byte DHCP broadcast from bring-up, which spans
two. Five-page frames are untested territory, and a transfer is the wrong
place to discover a wrap bug.
Default is now 256 bytes -> ~296-byte frame -> two pages, deliberately
close to the proven case. --block raises it once small blocks work; the GC
still caps at NB_BLOCK_MAX = 1024.
ring_next() also keeps the four raw descriptor bytes and the page it read
them from, and the error path prints them. When a length is rejected those
bytes ARE the diagnosis: 00 00 xx xx tells us the assembler wrote a
descriptor and the length is simply unexpected, whereas garbage tells us we
are reading the wrong page.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Without this, a successful transfer of a BROKEN build stranded you: the only
copy of a working test program had already been overwritten, so there was no
way to attempt another transfer without an SD card reader.
Write order is now temp -> verify -> rotate, and the ordering is the point:
- The image goes to "<name>.tmp" and is read back and compared BEFORE
anything existing is touched. If the transfer, the write or the verify
fails, the build you are running is still on the card untouched and you
can simply try again. Previously a failed write left the destination
half-overwritten.
- On success the existing build is rotated to "<name>.prev.dol" and the temp
file takes its place. So if the NEW build turns out to be broken, boot
the previous one from Swiss and transfer again from there. One generation
back is enough never to need a card reader.
The two extensions are chosen deliberately:
- the temp file has NO .dol extension, because Swiss lists .dol files and a
half-written image Swiss offers to boot is exactly what this avoids;
- the backup KEEPS .dol, because booting it from Swiss is the whole point of
keeping it.
remove()/rename() on a file that is not there is ignored -- that is just the
first update on a fresh card. If the final rename somehow fails, the message
names the .prev.dol path rather than leaving the user to guess where their
working build went.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Previous version launched the image it had just received, which is the one
thing that cannot be made safe: a broken build hangs the console and the
checks can only catch a truncated or non-DOL image, never a plausible but
broken one.
The flow is now receive -> write to SD -> boot /boot.dol:
- netboot_sd_write() mounts the card (auto-detecting SD2SP2, then SD Gecko
slot B, then slot A), writes the image to the path the host asked for,
and READS IT BACK AND COMPARES. A half-written .dol that still parses is
exactly the failure this design exists to avoid, and the card is the one
component here with no other integrity check.
- netboot_boot_file() then loads /boot.dol -- a known-good Swiss -- and
launches that instead.
So the only image this ever jumps into is one that was already known good. A
broken test build costs nothing: Swiss comes up and can load anything,
including the previous build. If the SD write or verify fails, nothing is
launched at all and the menu is still there.
The destination path travels in the DONE frame rather than being baked in, so
the host decides where the build lands (send-dol.py --dest, default
/gc_bba_test.dol).
libfat is unmounted before the jump: leaving the card mounted hands the next
image a filesystem libfat still thinks it owns, on an EXI channel it is about
to reinitialise.
Note the SD Gecko in memory-card slot A shares EXI channel 0 with the BBA
(channel 0, device 2). libogc arbitrates, but SD2SP2 is on its own channel
and avoids the question -- hence the detection order.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The launcher committed in b438960 would have hung the console, and reviewing
it against Dennis's suggestion to test with Swiss's boot.dol is what surfaced
it -- Swiss is known-good, so a hang could only have been the launcher, but I
would not have been able to tell that from "the transfer is broken".
Two distinct defects, both from the same oversight -- a DOL's sections load
from 0x80003100 upward, which is exactly where this program is running:
1. The copier was an ordinary C function in .text, so it overwrote its OWN
instructions partway through the copy.
2. The image was staged in a memalign'd buffer, which the destination sections
can overwrite while it is still being read from.
Fixes:
- netboot_stub.S: the copy/zero/cache-flush/jump sequence in position
independent assembly, copied into reserved memory and executed THERE. It
has no globals, no literal pool, no TOC references and no calls, because
any of those would read from the address it was LINKED at rather than the
one it is RUNNING at. It also does the dcbf/icbi pass the C version was
doing through DCFlushRange -- without it the CPU executes stale icache
lines at the entry point.
- netboot_reserve(): carves the top of MEM1 and hands it to
SYS_SetArena1Hi() so neither libogc nor malloc allocates there. Called
FIRST in main(), before the framebuffer.
- netboot_launch(): verifies every text/data section AND bss against the
reserved region and refuses (-3) if any would land on it, instead of
corrupting the staged image or the copier mid-flight. Also hands the new
image a stack inside the reserved tail.
The app now tells you on screen to send Swiss's boot.dol first, and the README
explains why: the launcher and the transfer can each be broken independently
and a hang looks identical, so the first send should be an image whose success
is unmistakable.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Copying to SD and rebooting is now the slowest part of the loop. Z in the
test app pulls a new .dol over the adapter and launches it.
Deliberately NOT built on an IP stack. Frames carry a private ethertype
(0x88B5, IEEE 802 local experimental 1) and a 12-byte header, so there is no
ARP, no IP, no checksums, and no libogc network driver competing with our raw
driver for the EXI channel. It reuses exactly the two paths the suite already
proves on hardware: bba_tx_bytes() for TX and the SPRAM ring at RRP for RX.
A side benefit is that each update is a few hundred round trips through that
path -- a soak test we did not have.
STOP-AND-WAIT is load-bearing, not laziness. The gateware does not consume
RRP, so RXFrameAssembler can overwrite ring pages the GC has not read yet;
there is no overflow protection. One block in flight means the ring never
holds more than one unread frame, so the missing protection cannot bite. Both
the header and the README say not to make this a sliding window without adding
RBFI-style protection first.
Failure behaviour, so a bad update never costs a power cycle:
- 30 s idle with no frames, or 5 s mid-transfer, aborts to the menu rather
than hanging.
- A duplicate block is RE-ACKed rather than ignored, because a duplicate
means our previous ACK was lost and re-ACKing is what lets the host move
on.
- netboot_receive() re-asserts the NCRA SR bit first: an earlier test may
have left receive disabled, and then this would wait forever for frames
the gateware is not storing.
- netboot_launch() refuses an image whose entry point or first text section
is not in MEM1 instead of jumping into a mis-parsed header.
The jump itself is the one unavoidable risk: once sections are copied and
interrupts are off, a bad image hangs the console hard enough to need a power
cycle. The MEM1 check is what stands between a truncated transfer and that.
Host side is scripts/send-dol.py (AF_PACKET, needs sudo). The GC's MAC is
discovered from its first ACK, so neither side needs an address configured.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
gc_bba_test/ builds a .dol that drives the adapter over raw EXI from the
console and reports pass/fail per test on the TV, navigable with the pad.
Uses libogc's EXI API against EXI0:2 (Serial Port 1) rather than its bba
network driver: driving the register file directly gives each check its own
verdict, so a failure points at a specific register instead of at
'networking'. Six suites - identity, registers, reset/control, EXI link
integrity (including an EXI clock-index sweep), ethernet TX/RX, SPRAM/DMA
streaming.
Encodes the hardware lessons from bring-up so the app cannot mislead:
* the device ID is a one-shot cleared by the first NCRA reset, so it is
reported SKIP on a re-run rather than FAIL
* TI means the frame reached the W5100, NOT the wire - the TX test says so
* register reads clock exactly the requested length (over-clocking
desynchronises the next transaction)
* TXDATA is written one byte per transaction (eff_addr auto-increments)
.devcontainer/Dockerfile gains the devkitPro gamecube-dev group. devkitPro
publishes no .deb on GitHub, so this uses their installer script against
apt.devkitpro.org -- which is 403 from inside the running container's egress
but reachable from a host-side docker build. Rebuild the container to get it.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Roflin