215 lines
8.2 KiB
Python
215 lines
8.2 KiB
Python
|
import os
|
||
|
|
import subprocess
|
||
|
|
|
||
|
|
from amaranth.build import *
|
||
|
|
from amaranth.vendor.xilinx_spartan_3_6 import *
|
||
|
|
from .resources import *
|
||
|
|
|
||
|
|
|
||
|
|
__all__ = ["MercuryPlatform"]
|
||
|
|
|
||
|
|
|
||
|
|
class MercuryPlatform(XilinxSpartan3APlatform):
|
||
|
|
"""
|
||
|
|
Original Mercury Board from Micro-Nova: https://www.micro-nova.com
|
||
|
|
|
||
|
|
Mercury Manual: https://www.micro-nova.com/s/mercury_rm.pdf
|
||
|
|
Mercury Schematic: https://www.micro-nova.com/s/mercury_schematic.pdf
|
||
|
|
|
||
|
|
The Mercury board is often paired with an extension board called the
|
||
|
|
Baseboard, which provides an ample set of I/O for FPGA beginners.
|
||
|
|
|
||
|
|
Baseboard Manual: https://www.micro-nova.com/s/baseboard_rm.pdf
|
||
|
|
Baseboard Schematics: https://www.micro-nova.com/s/baseboard_schematic.pdf
|
||
|
|
|
||
|
|
Mercury and Baseboard Resources: https://www.micro-nova.com/resources-mercury
|
||
|
|
"""
|
||
|
|
|
||
|
|
device = "xc3s200a"
|
||
|
|
package = "vq100"
|
||
|
|
speed = "4"
|
||
|
|
|
||
|
|
default_clk = "clk50"
|
||
|
|
resources = [
|
||
|
|
Resource("clk50", 0, Pins("P43", dir="i"),
|
||
|
|
Attrs(IOSTANDARD="LVCMOS33"), Clock(50e6)),
|
||
|
|
|
||
|
|
Resource("button", 0, Pins("P41", dir="i"),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
|
||
|
|
# The serial interface and flash memory have a shared SPI bus.
|
||
|
|
# FPGA is secondary.
|
||
|
|
SPIResource("spi_serial", 0, role="peripheral",
|
||
|
|
cs_n="P39", clk="P53", copi="P46", cipo="P51",
|
||
|
|
attrs=Attrs(IOSTANDARD="LVTTL"),
|
||
|
|
),
|
||
|
|
|
||
|
|
# FPGA is primary.
|
||
|
|
*SPIFlashResources(0,
|
||
|
|
cs_n="P27", clk="P53", copi="P46", cipo="P51",
|
||
|
|
attrs=Attrs(IOSTANDARD="LVTTL")
|
||
|
|
),
|
||
|
|
|
||
|
|
# ADC over SPI- FPGA is primary.
|
||
|
|
SPIResource("spi_adc", 0, role="controller",
|
||
|
|
cs_n="P12", clk="P9", copi="P10", cipo="P21",
|
||
|
|
attrs=Attrs(IOSTANDARD="LVTTL"),
|
||
|
|
),
|
||
|
|
|
||
|
|
# GPIO/SRAM Control
|
||
|
|
# 5V tolerant GPIO is shared w/ the SRAM (on 200k gate devices) using
|
||
|
|
# this pin. All GPIO except gpio:30 (and gpio:20, though see comment
|
||
|
|
# under SRAMResource) interface to the SRAM. On assertion, this signal
|
||
|
|
# will tristate the level-shifters, preventing any output on the 5V
|
||
|
|
# GPIO pins (including gpio:30 and gpio:20).
|
||
|
|
Resource("bussw_oe", 0, PinsN("P30N", dir="o"),
|
||
|
|
Attrs(IOSTANDARD="LVTTL"))
|
||
|
|
]
|
||
|
|
|
||
|
|
# Perhaps define some connectors as having a specific purpose- i.e. a 5V GPIO
|
||
|
|
# bus with data, peripheral-select, and control signals?
|
||
|
|
connectors = [
|
||
|
|
Connector("gpio", 0, """P59 P60 P61 P62 P64 P57
|
||
|
|
P56 P52 P50 P49 P85 P84
|
||
|
|
P83 P78 P77 P65 P70 P71
|
||
|
|
P72 P73 P5 P4 P6 P98
|
||
|
|
P94 P93 P90 P89 P88 P86"""), # 5V I/O- LVTTL.
|
||
|
|
Connector("dio", 0, "P20 P32 P33 P34 P35 P36 P37"), # Fast 3.3V IO
|
||
|
|
# (Directly attached to FPGA)- LVCMOS33.
|
||
|
|
Connector("clkio", 0, "P40 P44"), # Clock IO (Can be used as GPIO)-
|
||
|
|
# LVCMOS33.
|
||
|
|
Connector("input", 0, "P68 P97 P7 P82"), # Input-only pins- LVCMOS33.
|
||
|
|
Connector("led", 0, "P13 P15 P16 P19"), # LEDs can be used as pins
|
||
|
|
# as well- LVTTL.
|
||
|
|
Connector("pmod", 0, "P5 P4 P6 P98 P94 P93 P90 P89") # Baseboard PMOD.
|
||
|
|
# Overlaps w/ GPIO bus.
|
||
|
|
]
|
||
|
|
|
||
|
|
# Some default useful extensions. Attach to platform using:
|
||
|
|
# p.add_resources(p.leds)
|
||
|
|
# pmod_btn = plat.request("led")
|
||
|
|
leds = [
|
||
|
|
Resource("led", 0, Pins("1", dir="o", conn=("led", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("led", 1, Pins("2", dir="o", conn=("led", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("led", 2, Pins("3", dir="o", conn=("led", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("led", 3, Pins("4", dir="o", conn=("led", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
]
|
||
|
|
|
||
|
|
sram = [
|
||
|
|
SRAMResource(0,
|
||
|
|
cs_n="P3", we_n="gpio_0:29",
|
||
|
|
# According to the schematic, A19/Pin 25 on the SRAM is wired to
|
||
|
|
# gpio-0:20. However, according to the SRAM's datasheet, pin 25 is
|
||
|
|
# a NC. Do not expose for now.
|
||
|
|
a=""" gpio_0:1 gpio_0:2 gpio_0:3 gpio_0:4 gpio_0:5 gpio_0:6
|
||
|
|
gpio_0:7 gpio_0:8 gpio_0:9 gpio_0:10 gpio_0:11 gpio_0:12
|
||
|
|
gpio_0:13 gpio_0:14 gpio_0:15 gpio_0:16 gpio_0:17 gpio_0:18
|
||
|
|
gpio_0:19""",
|
||
|
|
d="""gpio_0:21 gpio_0:22 gpio_0:23 gpio_0:24 gpio_0:25 gpio_0:26
|
||
|
|
gpio_0:27 gpio_0:28""",
|
||
|
|
attrs=Attrs(IOSTANDARD="LVTTL", SLEW="FAST")
|
||
|
|
)
|
||
|
|
]
|
||
|
|
|
||
|
|
# The "serial port" is in fact over SPI. The creators of the board provide
|
||
|
|
# a VHDL file for talking over this interface. In light of space
|
||
|
|
# constraints and the fact that both the FT245RL and FPGA can BOTH be
|
||
|
|
# SPI primaries, however, it may be necessary to sacrifice two "high-speed"
|
||
|
|
# (DIO, INPUT) pins instead.
|
||
|
|
serial = [
|
||
|
|
# RX: FTDI D0, TX: FTDI D1
|
||
|
|
UARTResource(0, rx="input_0:1", tx="dio_0:1",
|
||
|
|
attrs=Attrs(IOSTANDARD="LVCMOS33"))
|
||
|
|
]
|
||
|
|
|
||
|
|
# The remaining peripherals only make sense w/ the Baseboard installed.
|
||
|
|
# See: http://www.micro-nova.com/mercury-baseboard/
|
||
|
|
_switches = [
|
||
|
|
Resource("switch", 0, Pins("1", dir="i", conn=("gpio", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("switch", 1, Pins("2", dir="i", conn=("gpio", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("switch", 2, Pins("3", dir="i", conn=("gpio", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("switch", 3, Pins("4", dir="i", conn=("gpio", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("switch", 4, Pins("5", dir="i", conn=("gpio", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("switch", 5, Pins("6", dir="i", conn=("gpio", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("switch", 6, Pins("7", dir="i", conn=("gpio", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("switch", 7, Pins("8", dir="i", conn=("gpio", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL"))
|
||
|
|
]
|
||
|
|
|
||
|
|
_buttons = [
|
||
|
|
Resource("button", 1, Pins("1", dir="i", conn=("input", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("button", 2, Pins("2", dir="i", conn=("input", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("button", 3, Pins("3", dir="i", conn=("input", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
Resource("button", 4, Pins("4", dir="i", conn=("input", 0)),
|
||
|
|
Attrs(IOSTANDARD="LVTTL"))
|
||
|
|
]
|
||
|
|
|
||
|
|
_vga = [
|
||
|
|
VGAResource(0,
|
||
|
|
r="dio_0:1 dio_0:2 dio_0:3",
|
||
|
|
g="dio_0:4 dio_0:5 dio_0:6",
|
||
|
|
b="dio_0:7 clkio_0:1",
|
||
|
|
hs="led_0:3", vs="led_0:4", invert_sync=True,
|
||
|
|
attrs=Attrs(IOSTANDARD="LVCMOS33", SLEW="FAST"))
|
||
|
|
]
|
||
|
|
|
||
|
|
_extclk = [
|
||
|
|
Resource("extclk", 0, Pins("1", dir="i", conn=("clkio", 1)),
|
||
|
|
Attrs(IOSTANDARD="LVCMOS33"))
|
||
|
|
]
|
||
|
|
|
||
|
|
_sevenseg = [
|
||
|
|
Display7SegResource(0,
|
||
|
|
a="gpio_0:13", b="gpio_0:14", c="gpio_0:15", d="gpio_0:16",
|
||
|
|
e="gpio_0:17", f="gpio_0:18", g="gpio_0:19", dp="gpio_0:20",
|
||
|
|
invert=True, attrs=Attrs(IOSTANDARD="LVTTL")
|
||
|
|
),
|
||
|
|
Resource("display_7seg_ctrl", 0,
|
||
|
|
Subsignal("en", Pins("9 10 11 12", dir="o", conn=("gpio", 0))),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")
|
||
|
|
)
|
||
|
|
]
|
||
|
|
|
||
|
|
_ps2 = [
|
||
|
|
PS2Resource(0,
|
||
|
|
clk="2", dat="1", conn=("led", 0), attrs=Attrs(IOSTANDARD="LVTTL")),
|
||
|
|
]
|
||
|
|
|
||
|
|
_audio = [
|
||
|
|
Resource("audio", 0,
|
||
|
|
Subsignal("l", Pins("30", dir="o", conn=("gpio", 0))),
|
||
|
|
Subsignal("r", Pins("29", dir="o", conn=("gpio", 0))),
|
||
|
|
Attrs(IOSTANDARD="LVTTL")
|
||
|
|
)
|
||
|
|
]
|
||
|
|
|
||
|
|
baseboard_sram = _buttons + _vga + _extclk + _ps2
|
||
|
|
baseboard_no_sram = baseboard_sram + _switches + _sevenseg + _audio
|
||
|
|
|
||
|
|
def toolchain_program(self, products, name):
|
||
|
|
# https://github.com/cr1901/mercpcl
|
||
|
|
mercpcl = os.environ.get("MERCPCL", "mercpcl")
|
||
|
|
with products.extract("{}.bin".format(name)) as bitstream_filename:
|
||
|
|
subprocess.check_call([mercpcl, bitstream_filename])
|
||
|
|
|
||
|
|
|
||
|
|
if __name__ == "__main__":
|
||
|
|
from .test.blinky import *
|
||
|
|
plat = MercuryPlatform()
|
||
|
|
plat.add_resources(plat.leds)
|
||
|
|
plat.build(Blinky(), do_program=True)
|